Fall Conference Discussions Cover Big Topics

When Glass Association of North America (GANA) divisions and committees met in Toronto last week for the group’s Fall Conference, members had plenty to discuss. Those in attendance covered topics ranging from ongoing interest in Building Information Modeling (BIM) to codes and standards, energy performance and more.

Courtesy of Tom Culp, Birch Point Consulting.

Courtesy of Tom Culp, Birch Point Consulting.

As part of the Building Envelope Contractors (BEC) technical committee, members have been discussing BIM, but Chuck Knickerbocker with Technical Glass Products, committee chair, said there have not been a lot of requests [on the subject] from this on BEC side. This, he said, is primarily because it seems manufacturers are the ones using it the most. He posed the question: is it trickling up to glaziers? Colin Blackford with Guardian Industries suggested the glass informational bulletin describe the importance for the contract glazier, how products are modeled and how BIM can be used at each point in the design process, etc. The document could also cover who uses BIM, why and the benefits at each level. A task group will continue to work toward developing the document.

Also during the BEC meeting, Knickerbocker said the Blueprint Reading and Labor estimating course has gone through a re-write and the edits are currently being reviewed. The group is hoping to have it wrapped up by the annual conference in March. In addition, both the Project Managers Reference Manual and the Commercial Systems Fenestration Manual are going through re-writes and revisions.

In the Energy Division meeting, Tom Culp with Birch Point Consulting, who serves as the GANA energy codes consultant, gave an update on what’s happening in terms of codes and standards. He said states are considering adoption of the 2015 IECC on the residential side, while the commercial side is seeing activity around the 2016 edition of ASHRAE 90.1, as well as the IgCC and ASHRAE 189.1.

Speaking of ASHRAE 90.1 he said the biggest issues involve U-factor solar heat gain co-efficient (SHGC) and possibly visible transmittance (VT)/SHGC. Looking at performance and cost effectiveness calculations, but the focus is on lower U-factors in Zones 4-8.

Other issues being discussed at ASHRAE include requiring a certain amount of floor area to be in daylight zones and/or certain amount of lighting to be daylight controlled, as well as corrections being made to the SHGC credit for exterior shading. He said they are also looking at clean up to building/window orientation requirements. He added it’s “important to note GANA and the Aluminum Extrusions Council are the only window-related organizations with voting representation on ASHRAE.”

Culp also talked some about ASHRAE 189.3 – healthcare, a new standard under development for green hospital and health care facilities. He explained it’s written as an overlay to 189.1 and has the same envelope and daylighting requirements. They have specifically removed the renewable energy requirements (either BIPV or renewable energy credits). Culp said comments will be filed to restore this section.

Within NFRC, this group is considering the use of a new standard solar spectrum for SHGC and VT ratings, which he said will have big implications for code compliance and product developments. If NFRC decides to make any change, it will be no earlier than January 2018 and would coordinate with Energy Star and the codes.

Also, he said NFRC is continuing to look at CMA improvements; improvements to CMAST software usability; and implementing changes to improve accuracy for low U-factor products. There was also a ballot to limit the use of the site-built program to encourage greater use of CMA.

Also within the energy division meeting, Helen Sanders with SageGlass, who serves as the committee chair, reported that the windows Product Category Rule (PCR), which is being developed jointly with the American Architectural Manufacturers Association, the Insulating Glass Manufacturers Alliance and the Window and Door Manufacturers Association, is nearing completion. She also reported that GANA will be looking to develop a PCR for fabricated glass that will cover laminated, IG and tempered.

She explained PCRs help ensure apples-to-apples data and that companies are measuring the environmental impact of products the same way. Saunders also said architects are increasingly asking about PCRs. “You have a PCR so everyone does the Life Cycle Assessment the same way; so everything is comparable to one another,” she said.

This article is from USGNN™, the daily e-newsletter that covers the latest glass industry news. Click HERE to sign up—there is no charge. Interested in a deeper dive? Free subscriptions to USGlass magazine in print or digital format are available. Subscribe at no charge Sign up today.

This entry was posted in Featured News, Today's News and tagged , , , , , , , , , , . Bookmark the permalink.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.